Este sitio web utiliza cookies propias y de terceros para mejorar nuestros servicios y optimizar su navegación. Si continúa navegando, consideramos que acepta nuestra política de cookies.

Beyem Neocal Sanamur

Beyem Neocal Sanamur

Two-component dehumidifying lime mortar for renovating masonry with rising damp.

About this product

BEYEM NEOCAL SANAMUR is a two- component dehumidifying lime mortar for renovating masonry with rising damp in buildings. Formulated with mixed binders, lime, selected white aggregates, and special additives. Fine and smooth finish.  Indoor environment quality. Classifed as  A+ class according to Décret nº. 2011-321 (France). Free of radionuclides.

Benefits
  • Rainwater- proof. Weather resistant.
  • Macroporous. High water vapour permeability.  
  • Salt-resistant.
  • Allows evaporation of water.
  • Excellent adhesion.
  • Fine  and extra-white finish .
  • Compatible with old masonry brickworks/walls.
  • Mechanical strengths corresponding to lime mortars.
  • Great plasticity.
  • Suitable for internal or external walls.
  • Very low VOCs  emissions.
  • Radiation-free certificate.
  • Mineral product.
Use

Dehumidifying lime mortar for renovating masonry affected by rising damp, filtration, condensation and efflorescences both in building rehabilitation and new construction. Fine finish. Interior and exterior situations. 

Substrates

BEYEM NEOCAL SANAMUR  is  suitable for:

  • Brickwork enclosures, walls , rendering mortars  and plasters affected by humidity.
Preparation of substrates

Substrates must be clean, compact and free of substances that reduce adhesion such as dust, oil, grease and with no loose material. Substrates must submit an adequate porosity, flatness and surface roughness. In old substrates, residues of other coatings, dirt, dust and microorganisms must be completely removed. To eliminate microorganisms, use a biocide cleaner indicated for this purpose. If necessary, use sandblasting technique or wash with high pressure water. In old substrates, all friable elements must be completely removed and the joints emptied. Fill the gaps of the substrate  with BEYEM NEOCAL SANAMUR. Let harden. Dampen substrates with water to cool down if they should be too warm, in case of wind or over absorbent substrates and wait until the thin layer of water disappears. It is a good practice curing with a fine spray of clean water 24 h after application. Curing operation is essential to avoid  rapid drying and depends on the degree of porosity and surface absorption. Do not apply on cellular concrete, gypsum-based plasters, paint, metal surfaces, plastic, surface waterproofing products  or materials with low mechanical properties.

Instructions for use

BEYEM NEOCAL SANAMUR is presented in adequate proportions of its two components. Pour the component B (liquid) into a clean container and add the component A (powder) little by little. Mix  until a homogeneous, creamy and lump-free paste is obtained. Let the mix stand for 5 minutes before application. Spread the mixed product with a trowel (in case of manually or mechanically application) leaving  8-10 mm of average  thickness depending on the desired finish. Thicknesses up to 20-25 mm can be applied in layers of 10 mm thick per day. Press to ensure adhesion. Smooth with a ruler the applied material to regulate thickness. When BEYEM NEOCAL  SANAMUR is green (set but not fully hardened) it should be finished using the appropriate tool  depending on the desired texture (trowelled, fine scraping…). Time until finishing depends of substrate, temperature and humidity. 

Cautions and recommendations
  • Do not apply below 5ºC or above 30ºC.
  • Do not apply when there is risk of frost, rain, strong wind or direct sunlight.
  • Do not vary the mixing ratio of the components.
  • Do not apply on plasters, old paints, or degraded substrates without first treating them.
  • Lime mortars have a slower setting, so the hardening time increases.
  • It is not advisable to apply on horizontal or sloped surfaces in exterior situations.
  • Protect top edges of facade from rainwater penetration.
  • Expansion joints should be included as required by the substrate and respected by all applied materials.
  • Reinforcement with alkali resistant fiberglass mesh  may also be required, dependent upon substrate condition ( junctions of different surfaces, corners of voids…),  project specification or applied thickness greater than recommended.
  • In cases of extreme rising damp, an horizontal chemical barrier is recommended.
  • BEYEM NEOCAL SANAMUR must be used in conjunction with other techniques where necessary.
  • Consult to the Technical Department in case of doubt or in cases not described.
Technical data

Product identity. Properties of mixture and application data

Appearance  and color

 

Component A

White powder

Component B

Whitish liquid

Bulk density

≈ 1400 Kg/m3

Density of the mix

≈ 1750 Kg/m3

Grading

0-1 mm

Maximum thickness  per layer

10 mm

Maximum thickness application

25 mm (three layers)

Coverage

14 Kg/m2  per cm of thickness

Tariff code Component  A

3824.50.90.00

Tariff code Component  B

3209.10.00.00

Final performances

 

Type

R CS II

Adhesion

≥ 0,4 MPa

Compressive strength

≥ 1,5 MPa 

Capillary water absorption

≥ 0.3 (after 24 hours)

Water penetration after water absorption

≤ 5 mm

Water vapor permeability

µ ≤ 15

Thermal conductivity

0,67 W/m·k

Reaction to fire

Euroclass F

Total VOCs (28 days)

< 500 µg/m3

Radioactivity index (U, Ra, Pb, Th, others)

I = 0,047

Packaging

BEYEM NEOCAL SANAMUR is packed  in pre-measured batches of 31,5 kg (25 kg plastic lined paper bags – Component A-  and 6,5 kg plastic bottle – Component B-).

Storage: when stored unopened in a cool dry place, shelf life is 12 months from date of manufacture.

Cleaning tools

Tools can be cleaned easily with water before the product hardens. Hardened product can be removed only mechanically.

Project specification

Renovation of  masonries deteriorated by the presence of rising damp, filtrations, condensations and soluble salts, must be carried out with COVs and radiation free, two-component dehumidifying lime mortar compliant with EN 998-1- Class R CSII, such as BEYEM NEOCAL SANAMUR manufactured by Rodacal Beyem Company. Coverage will be ≈ 1,4 kg/m2 per mm of thickness. The substrate must be clean, sound, compact and dimensionally stable. Expansion joints must be respected.

Health and Safety

For further and complete information about the safe use of our product please refer to our latest version of the Safety Data Sheet, which is available upon request.

Disposal of the product and packaging must be in accordance with current legislation. This is responsibility of the final product user.

Certifications

Technical Data Sheet

Ficha de Seguridad Componente A

Ficha de Seguridad Componente B

Declaration of Performance

Certificate of Factory Production Control

Volatile Organic Compounds Declaration

Radiation-Free Certificate

Certificate of Quality Management System ISO 9001

Certificate of R+D+i Management System UNE 166002

Up Send to a friendSend to a friend Go backGo back