Beyem B-R

Beyem B-R
Beyem B-R

Lightweight, scraped finish, rainwater-proof   one coat mortar  for  facade decoration. 

About this product

BEYEM B-R is a lightweight  rainwater-proof   one coat mortar  for decoration of facades. Formulated with white cement, selected and lightweight aggregates, special additives,  and inorganic pigments.

It allows constant hygrometric exchange between the substrate and the environment. 

Benefits
  • Suitable for spray render and pump machines or manual applications.
  • Good mechanical strengths.
  • D.I.T Plus issued by Ietcc.
  • Applicable  directly to the building enclosure.
  • Lightweight. Excellent  workability.
  • Rough and scraped finishes.
  • Rainwater-proof and permeable to water vapour.
  • Low maintenance.
  • Suitable for internal and external walls.
  • New construction and rehabilitation.
  • Through-coloured render. Wide range of colours.
Use

Mineral and rainwater-proof one coat mortar for facades, brickwork and  concrete block enclosures. Rough and scraped finishes. Suitable for  walls and ceilings  both in  interior and exterior situations, manually or mechanically. Through coloured for low maintenance. 

Substrates

BEYEM B-R is suitable for:

  • Brickwork. Ceramic bricks.
  • Concrete blocks.
  • Concrete  (treated with BEYEM UNIÓN MORTEROS adhesion promoter primer).
  • Cement based substrates.
Preparation of substrates

Substrates must be clean, compact and  free of substances that reduce adhesion such as dust, oil, grease and with no loose material. Substrates must submit an adequate porosity and surface roughness. Uneven areas must be corrected.  Dampen substrates with water  to cool down if they should be too warm, in case of wind or over absorbent substrates  and wait until the thin layer of water disappears. It is a good practice curing with a fine spray of clean water  24 h after application.

Do not apply on cellular concrete, gypsum based plasters, paint, plastic, wood or materials with  low mechanical properties.

Instructions for use

Mix manually of mechanically BEYEM B-R with 5,25-6,25 l per bag of clean water until a homogeneous, creamy and lump-free paste  is obtained. Let the mix stand for 5 minutes before application.

To apply with render  spray machine, it´s necessary to set the relation water/mortar  and pump pressure depending on section and length of hose  and climatology conditions. It´s important to maintain the  variables affecting the properties of the applied mortar (distance to the wall, angle of application and water proportion). Spread the mixed product with a trowel (in case of manually or mechanically application) leaving  12-15 mm of average  thickness, after marking the pieces by using PVC splines. Press to ensure adhesion and expel the air contained in the pores. Smooth with a ruler the applied material to regulate thickness. When BEYEM B-R is green (set but not fully hardened) it should be scraped with a circular action using a scarping tool. To avoid changes in tone always carry out this procedure at the same hardening point. Thoroughly brush down the surface of the scraped finish using a soft bristle brush. 

Cautions and recommendations
  • Always mix with the specified amount of water.
  • Do not apply below 5ºC or above 30ºC.
  • Do not apply when there is  risk of frost, rain, strong wind or direct sunlight.
  • Above 15 mm of thickness, apply the product in two layers, leaving a roughness surface in the first to improve the adhesion of the second layer.
  • It is not advisable to apply on horizontal or sloped surfaces. 
  • Protect top edges of facade from rainwater penetration.
  • The minimum finishing thickness of render must be 10 mm, to contribute actively to the  waterproofing of surface.
  • Reinforcement with alkali resistant fiberglass mesh  may also be required, dependent upon substrate condition ( junctions of different surfaces, corners of voids…)  and project specification.
  • Demarcate pieces of work using PVC battens previously placed.
  • Expansion joints should be included as required by the substrate and respected by all applied materials.
  • It is necessary to use a primer on too high absorption substrates, as a cellular concrete, or on very low absorption substrates.
  • Variations in weather conditions during application, and the application in several phases can produce changes in tone.
Technical data

Product identity. Properties of mixture and application data

Appearance

Powder

Colour

Colour Chart

Bulk density

≈ 1500 Kg/m3

Density of the mix

≈ 1750 Kg/m3

% Particles larger than 1 mm

< 12%

Mixing water,% 

± 23%

Minimum finishing thickness

10 mm

Maximum layer thickness

15 mm

Coverage

15 Kg/m2  per cm of thickness

Tariff code

3824.50.90.00

Final performances

 

Type

OC CSIV W2

Adhesion after weathering cycles

≥ 0,50 MPa

Compressive strength

≥ 6,0 MPa

Shrinkage

≤ 1 mm/m

Capillary water absorption

< 0,2 kg/m2min1/2

Water permeability after weathering cycles

≤ 1 ml/cm2 , after 48 h

Water vapour permeability

µ < 15

Thermal conductivity

0,67 W/m·K

Reaction to fire

Euroclass  A1

Packaging

BEYEM B-R is packed 25 kg plastic lined paper bags.

Storage:  when stored unopened in a cool dry place, shelf life is 12 months from date of manufacture.

Cleaning tools

Tools can be cleaned easily with water  before the product hardens. Hardened product can be remove only mechanically.

Project specification

Coloured rendered surfaces with scraped or rough  finish, must be carried out with lightweight, rainwater-proof, one coat dry mortar  compliant with EN 998-1- Class OC CSIV W2, such as Beyem B-R (D.I.T Plus nº 411) manufactured by Rodacal Beyem Company. Coverage will be ≈ 15 kg/m2 per cm of  thickness. The substrate must be clean, sound, compact and dimensionally stable. Expansion joints must be respected.

Health and Safety

For further and complete information about the safe use of our product please refer to our latest version of the Safety Data Sheet, which is available upon request.

Disposal of the product and packaging must be in accordance with current legislation. This is  responsibility of the final product user.

Certifications

Technical Data Sheet

Safety Data Sheet

Declaration of Performance

Certificate of Factory Production Control

DIT Plus Certificate Nº411p/15

Certificate of Quality Management System ISO 9001

Certificate of R+D+i Management System UNE 166002

Carta de colores Beyem B-R

Up Send to a friendSend to a friend Go backGo back

Ctra. Madrid-Alicante, Km. 213 (Extramuro)
02630 La Roda - Albacete (España)
Telephone 1: 967 440 018 Fax: 967 442 474
E-Mail: rodacal@rodacal.com

Web Design and Development Im3diA comunicación
This website is optimized for browsers Chrome, Internet Explorer 9 and Firefox 4.0.