Este sitio web utiliza cookies propias y de terceros para mejorar nuestros servicios y optimizar su navegación. Si continúa navegando, consideramos que acepta nuestra política de cookies.

Beyem 1,2,3

Beyem 1,2,3

Ultra-fast setting mortar for anchoring, fixing and little repairs.

About this product

BEYEM 1,2,3  is a ultra-fast setting mortar  formulated with hydraulic binders and  selected aggregates. Especially suitable for non structural anchoring, fixing and little repairs. For plugging leaks and seal joints to resist inflow of water.

Benefits
  • Set in 5 minutes.
  • Free of chlorides.
  • Easy to apply.
  • High  early  mechanical strength.
  • Waterproof.
  • Excellent bond strength.
  • Non-shrink mortar.
  • For interior and exterior use.
  • High  final  mechanical strengths.
Use

Non structural anchoring and immediate embedings. Stopping of running water and seepage through cracks and holes in masonry, walls, dams, wells, tanks, wall and floor junctions etc. It can also be used as a

grout around pipes and conduits and as a rapid anchoring product of masonry elements, toilets, baseboards… or as a rapid-set filler. Masonry brickwork in walls and fine partitions. Cavity filling. Molding of holes and edges of windows and doors. For interior and exterior use. 

Substrates

BEYEM 1,2,3  is suitable for:

  • Concrete and concrete blocks.
  • Brickwork. Ceramic bricks.
  • Cement  based substrates
Preparation of substrates

Substrates must be clean, compact and  free of substances that reduce adhesion such as dust, oil, paint, grease and with no loose material. Substrates must have already completed the curing period of hygrometric shrinkage. Dampen substrates with water  to cool down if they should be too warm, in case of wind or over absorbent substrates  and wait until the thin layer of water disappears. Do not  use on  gypsum based plasters or paint.  

Instructions for use

Mix manually of mechanically BEYEM 1,2,3  with  5,5-6,0 l per bag of clean water until a homogeneous, creamy and lump-free paste  is obtained.  Apply immediately the product using a trowel, filling the cavity in case of an anchorage. Beyem 1,2,3 starts to harden in 2/4 minutes and finishes in 5/6 minutes. Mix only sufficient material that can be applied using available labour and equipment taking into account the pot life of product.

Cautions and recommendations
  • Anchors must be made verifying the depth and width with respect to the diameter of the anchorage.
  • Do not apply below 5ºC or above 30ºC.
  • Do not apply when there is  risk of frost, rain, strong wind or direct sunlight.
  • Do not re-mix  product residues that have started to harden, because that causes a decrease in the properties of the mortar.
  • Protect the mortar surface of early dehydration, using suitable  curing methods to obtain a perfect setting.
  • It is possible to delay initial setting time of mortar using setting retarders  (contact Technical Support).
  • It is recommended to mix small amounts of BEYEM 1,2,3
  • Always mix with the specified amount of water.
  • Do not use BEYEM 1,2,3 for concrete repair nor machinery anchors.
  • Do not add more water than recommended amount, because that may cause a decrease in the mechanical properties of mortar and a delay in its setting time.
  • Setting time of mortar increases with low  temperatures.
Technical data

Product identity. Properties of mixture and application data

Appearance

Powder

Color

Grayish brown

Bulk density

≈ 1200 Kg/m3

Grading

0-1 mm

Mixing water,% 

± 23%

Initial setting time

2-4 min

Coverage

According to use

Tariff code

3824.50.90.00

Final performances

 

Compressive strength

≥ 30,0 MPa

Compressive strength after  1h

≥ 1,5 MPa

Compressive strength after  24h

≥ 5,0 MPa

Packaging

BEYEM 1,2,3  is packed 25 kg plastic lined paper bags and 5 kg plastic bags.

Storage:  when stored unopened in a cool dry place, shelf life is 12 months from date of manufacture.

Cleaning tools

Tools can be cleaned easily with water  before the product hardens. Hardened product can be remove only mechanically.

 
Project specification

Non structural anchoring, cavity fillings and immediate embedings must be carried out with ultra-fast setting mortar, such as Beyem 1,2,3  manufactured by Rodacal Beyem Company. The substrate must be clean, sound, compact free of substances that reduce adhesion. substrate must be dampened before product application. 

Health and Safety

For further and complete information about the safe use of our product please refer to our latest version of the Safety Data Sheet, which is available upon request.

Disposal of the product and packaging must be in accordance with current legislation. This is  responsibility of the final product user.

Certifications

Technical Data sheet

Safety Data Sheet

Certificate of Quality Management System ISO 9001

Certificate of R+D+i Management System UNE 166002

Up Send to a friendSend to a friend Go backGo back